We use our 800 lb. Lavina diamond grinder to mechanically profile every floor to CSP-3 — the industry-recognized standard for maximum coating adhesion. We spend approximately one-third of every project on prep: grinding, vacuuming, crack repair, and slab inspection before a drop of coating is applied.

We also test every slab for moisture vapor transmission before selecting a system. If moisture readings warrant it, we install a moisture vapor barrier as a foundation layer before the basecoat — skipping this step is one of the most common reasons coatings fail prematurely in Iowa's climate. We never substitute acid washing for mechanical grinding, and we never skip the moisture assessment.

Yes — for the vast majority of residential projects. Because we use polyurea and polyaspartic systems instead of traditional epoxy, our coatings cure in hours rather than days. Most standard garage floors are fully installed in 5–10 hours depending on square footage.

You can walk on the floor within 12 hours of application. Full vehicle traffic is safe after 24–36 hours. Larger commercial or multi-area projects may require two days; your estimator will confirm the timeline clearly before any work begins.

Absolutely — crack and spall repair is a standard part of every Revival installation. We use 100% solids polyurea filler to address cracks, chips, and surface imperfections before any coating is applied. The decorative flake system then camouflages the repaired areas seamlessly.

In many cases, coating is significantly more cost-effective than demolishing and replacing the slab. We get calls regularly from homeowners who assumed their floor was beyond saving — and we rescue it. Send us photos or schedule a free on-site assessment and we'll give you an honest answer.

Our polyurea basecoat can be installed in temperatures as low as –40°F — a major advantage over epoxy, which fails to cure reliably in cold Iowa winters. Polyaspartic topcoats also perform across a wide range of temperature and humidity conditions.

That said, we monitor every job day carefully. If there's active moisture on the slab or extreme cold-soak conditions, we address it before starting. Your crew will not begin a job they aren't confident will last — that's the Revival standard, year-round.

Clear everything off the floor — vehicles, bikes, shelving, storage bins, and anything stored directly on the concrete. The entire surface needs to be open and accessible for grinding and coating. We handle all dust containment, vacuuming, and cleanup — you don't need to mask, cover, or prep anything yourself.

If you have utility equipment or large items that can't easily be moved, just let your project coordinator know ahead of time and we'll plan around it. Your scheduling call will cover all the details.

Polyurea is a high-performance polymer used to coat military vehicles, steel bridges, and industrial pipelines — and for good reason. For floors, it's 4× stronger than standard epoxy, cures in hours, remains flexible under temperature swings (so it won't crack as your slab expands and contracts), and bonds permanently to properly prepared concrete.

Standard epoxy is rigid and brittle once cured. It's highly sensitive to moisture and temperature during application, yellows under UV exposure, and typically begins to fail within 3–5 years in high-use areas. Revival uses polyurea and polyaspartic systems exclusively — no epoxy, no shortcuts.

Polyaspartic is a sub-category of aliphatic polyurea engineered specifically for UV stability, optical clarity, and superior surface hardness. We apply it as the final topcoat over the polyurea basecoat to deliver a gorgeous, glass-smooth finish that holds its color, resists scratching, and stands up to chemicals for the life of the floor.

Think of the system in two layers: the polyurea basecoat provides the structural bond and strength, and the polyaspartic topcoat provides the beauty and UV protection. Together, they create a floor that outperforms anything else on the residential or commercial market.

No. Our UV-stable polyaspartic topcoat is engineered to resist photodegradation — the process that causes yellowing and ambering in lesser coatings. It holds its color and clarity for the full life of the floor, including sun-exposed patios, pool decks, and garages with south-facing doors.

If you've ever seen a garage floor with a yellow or orange tint, that's almost always an epoxy coating that has degraded — typically within 12–18 months of installation in UV-exposed environments. With Revival's system, that's simply not a concern.

Yes. Our standard vinyl flake system already provides meaningful texture and grip compared to bare or painted concrete. For applications requiring enhanced slip resistance — pool decks, commercial kitchens, shop floors, or entryways — we add anti-slip aggregate directly into the polyaspartic topcoat for increased traction even when wet.

We'll dial in the right texture level for your specific use case during the consultation. The goal is always a floor that is safe, easy to clean, and visually excellent — all three, together.

Flake System — Our most popular system. Colorful vinyl flakes broadcast into a polyurea basecoat and finished with a clear polyaspartic topcoat. Perfect for garages, basements, patios, and showrooms. Virtually unlimited color options.

Quartz System — Double-broadcast quartz granules for maximum durability and UV resistance. Ideal for pool decks, commercial kitchens, and high-traffic exterior surfaces requiring extra grit.

Grind & Clear — The surface is ground smooth and sealed with a chemical-resistant clear coat for a polished, modern industrial look. Great for offices, retail spaces, and warehouses.

Solid Color — A clean, uniform polyurea solid-color system for spaces requiring a specific color match or minimal aesthetic.

It depends on the condition of the existing epoxy. If it's still tightly bonded, we can diamond grind it, create a proper profile, and apply our system on top. If the epoxy is peeling, bubbling, or delaminating, it must be fully ground off before we can proceed — otherwise we'd just be coating over a failing surface, and the new system would fail too.

We assess this at no cost during every free estimate. We'll tell you exactly what's needed and what it will cost — no surprises.

Most residential garage floor coatings in Greater Des Moines range from $1,500 to $4,500 depending on the square footage, surface condition, repairs needed, and system selected. A standard two-car garage typically falls in the $2,000–$3,200 range.

Every project is priced on-site after a free, no-pressure consultation. We provide a firm, all-inclusive quote before any work begins — no hidden fees, no surprise add-ons after the job is done. Evening and Saturday appointments are available.

Yes. Revival offers flexible financing options to make your project accessible without waiting. Financing is available with approved credit and can be discussed during your free estimate appointment. Ask your estimator for details or visit our Financing page.

All residential floor coating installations are backed by a 15-year transferable warranty — one of the strongest guarantees in the Greater Des Moines market. Commercial installations carry a 5-year warranty. The transferable nature of the warranty means it adds genuine resale value if you ever sell your home.

The warranty covers peeling, delamination, and product failure under normal use. Your install crew will walk you through all warranty terms and leave you with documentation after the job is complete.

When installed correctly over properly prepared concrete, Revival's coating systems are designed to be permanent. The polyurea basecoat forms a mechanical bond — not just a surface adhesion — meaning it won't peel or chip under normal conditions even after decades of use.

The most common reason floor coatings fail prematurely is inadequate surface preparation by the installer, not the product. Because we invest heavily in the prep phase — diamond grinding to CSP-3, complete crack repair, full vacuuming — our installations routinely outlast the warranty period by many years.

Maintenance is one of the best things about a Revival floor — it's genuinely easy. Sweeping or dust-mopping handles everyday dirt. For deeper cleaning, mop with warm water and mild soap — Dawn or Simple Green work great. Avoid abrasive scrub pads or harsh solvents like acetone or paint thinner.

For tire marks or embedded grease, a non-abrasive degreaser like CLR works well. A garden hose or pressure washer on a low setting is safe for outdoor surfaces. You'll also receive a printed care card after installation with everything you need to keep the floor looking its best.

Revival's polyaspartic topcoat is highly resistant to oil, gas, transmission fluid, brake fluid, antifreeze, and most household and automotive chemicals. The non-porous surface prevents liquids from soaking in the way bare concrete does — in most cases, a quick wipe is all that's needed.

We recommend wiping up any spill promptly rather than letting it sit. Very harsh solvents at high concentrations (acetone, paint thinner, strong acids) should always be cleaned up immediately. Under normal garage and residential use, staining is simply not a concern.

No. If you follow our maintenance and cleaning guidelines, you will not need to reseal the coating. The polyaspartic topcoat is a long-term final surface — not a sacrificial layer that needs periodic refreshing like wax or natural stone sealer.

In extremely high-traffic commercial environments, some customers opt for a maintenance topcoat after many years to restore the original gloss. For residential use, this is rarely if ever necessary within the 15-year warranty period.

You can walk lightly on the floor within 12 hours of application. For vehicle traffic — parking, driving in, and full garage use — we recommend waiting a full 24–36 hours. Cure times are slightly longer in cold temperatures, and your installation crew will give you a specific window based on the conditions on your project day.

We leave every customer with a printed care card covering first-week recommendations so nothing is left to memory.